THE PROBLEM
Sunday morning shouldn't feel like this.
WHAT TALLY DOES
Fixes the problems you haven't had yet.
Signal Lost — Tally Switches Instantly
Multi-signal diagnosis detects video loss, audio silence, and ATEM disconnections. Automatically switches to a safe source, alerts your TD, and verifies stability before switching back.
Stream Goes Down — Tally Fixes It
Auto-recovery restarts your stream before the congregation even notices. Works with OBS, vMix, and hardware encoders.
Slack + Telegram Alerts
Your TD gets an alert on Slack or Telegram in seconds — with diagnosis steps and one-tap acknowledge. Escalation if nobody responds in 5 minutes.
Automated System Check
Green-light confirmation 30 min before every service. Every device tested, every connection verified. No more manual walkthroughs.
Deep ProPresenter + ATEM Control
Cut cameras, advance slides, trigger looks, send stage messages, start timers — all from your phone or Telegram.
Natural Language Control
Type "cut to camera 2 then start recording" and Tally does it. AI-powered command parsing understands plain English — no menus needed.
Full Rundown Planner
Drag-and-drop service planning with smart timing, hard start times, and over/under tracking. Go live with cue-by-cue show control, 7 output views, and collaborative real-time editing.
AI Document Import
Upload a PDF, Word doc, or PowerPoint and AI converts it into a structured rundown automatically. No manual re-entry — just review and go.
Live Show Mode
GO/Back navigation with real-time elapsed and remaining timers. Pause and resume mid-service with automatic timer adjustments — your confidence monitors stay accurate.
AI Autopilot
Create step-by-step production rundowns that auto-advance on a timer during service. Up to 25 steps on Enterprise.
Self-Service Church Portal
Every church gets their own dashboard — manage TDs with viewer, operator, and admin access levels, set service schedules, view session history, configure alerts, and handle billing. TDs log in directly with their own credentials.
Post-Service Debrief
Every service gets a timeline: what happened, what broke, what auto-recovered. Session recaps push into Planning Center automatically.
Planning Center Sync + Write-Back
Pull service times automatically. After each service, production notes push back into the plan — no manual data entry.
Guest TD Tokens
Generate temporary access tokens for guest TDs or volunteers. Auto-expire in 24 hours. Full audit trail of every action.
On-Call TD Rotation
Weekly rotation with Telegram swap commands. Alerts route to whoever is on-call — not everyone on the team.
Monthly Health Reports
Uptime stats, incidents, and auto-recoveries per church. Monthly health reports keep leadership in the loop — delivered on the 1st of every month.
AI Setup Assistant
Upload a patch list or camera plot and Tally auto-configures your mixer channels and ATEM input labels. Parses CSVs, PDFs, and photos using AI vision — setup in minutes, not hours.
Built For Multi-Room
Start with one room on Connect, scale to 3 on Plus, 5 on Pro, or unlimited on Enterprise — without adding chaos to Sunday.
Any Encoder, Any Workflow
OBS, vMix, Ecamm, Blackmagic, Teradek, YoloBox, Epiphan, AJA HELO — Tally monitors whatever encoder you run.
Live Video Preview
See your program feed from anywhere. H.264 monitoring stream routed securely — requires a Tally Box hardware encoder. In development.
15 Step-by-Step How-To Guides
Plain-language setup guides with Quick Start summaries, difficulty ratings, and collapsible advanced details. Written for volunteers, not engineers.
Safety Gates for Live Commands
Tally warns before executing dangerous commands while you’re live — like stopping a stream or switching sources. Confirms with your TD before anything risky happens.
Full Audio Console Control
EQ, compression, gates, faders, mute/solo — control every channel on your Allen & Heath, Behringer, Midas, or Yamaha console from Telegram.
One-Tap Preset Recall
Save complex multi-device setups and recall them instantly. Mixer scenes, ATEM macros, OBS scene collections — one tap to switch your entire production config.
Mobile-Ready Church Portal
Your church dashboard works on any device. Check equipment status, manage TDs, and review sessions from your iPhone during service.
Smart Plug Power Cycling
Discover and control Shelly smart plugs on your network. Power-cycle encoders, mixers, or any racked gear remotely — auto-discovered via mDNS with real-time power and voltage monitoring.
Color-Coded Encoder Metrics
CPU usage, bitrate, FPS, and stream health at a glance with green/yellow/red thresholds. Covers OBS, vMix, hardware encoders, and CDN platforms — with automatic alerts when metrics cross into warning or critical zones.
Works with 23+ integrations across switchers, encoders, audio, and presentation software.
View Compatible Hardware →HOW AUTO-RECOVERY WORKS
It breaks. Tally fixes it.
Automatic detection, verification, and recovery — before your congregation notices.
Tally spots the drop — encoder, stream, audio, or video signal
Confirms it’s a real outage, not a momentary blip
Restarts the stream, re-engages the encoder, switches to backup
Stream verified healthy. Your TD gets an alert. Congregation never knows.
THE APP
See exactly what's happening.
From anywhere.
The Tally client installs on your booth computer in minutes. Your TD sees every device status at a glance — switch between rooms with the room selector and see every church from your phone.
RUNDOWN PLANNER
Plan the service. Run the show. Nail the timing.
Full rundown planning with live show control, 7 output views, collaborative editing, and AI-powered document import — built for church production teams.
Run your show
One tap to enter live show mode. GO and Back buttons advance cue-by-cue with real-time elapsed/remaining timers. Pause and resume mid-service with automatic time adjustments — your countdown clocks stay accurate.
7 OUTPUT VIEWS
One rundown. Every screen covered.
Share output views with a link — operators don't need a login.
Included in all plans. 30-day free trial.
INTEGRATIONS
WORKS WITH EVERYTHING
IN YOUR RACK
23 integrations and counting. If it's in your booth, Tally monitors it.
HOW IT WORKS
Three steps. Ten minutes.
Install
10-minute setup. Run the app on your booth computer. Connect to your ATEM, OBS, and Companion by entering their IP addresses. The AI Setup Assistant can auto-configure your mixer and camera labels from a patch list.
Connect
Your church appears live on the Tally dashboard. Every device, every status — instantly visible from anywhere.
Relax
Tally watches your entire production. If something breaks, it fixes it first — then tells you.
ROI CALCULATOR
See what streaming failures actually cost you.
Adjust the sliders to match your church. Tally pays for itself after a single prevented incident.
Includes lost donations, volunteer time, reputation impact, and re-engagement costs.
PRICING
Simple, honest pricing.
30-day free trial for every church — no credit card required. Cancel anytime.
Connect
Monitoring, alerts, and remote control for a single room.
- ✓1 room included
- ✓3 core integrations (ATEM, OBS, vMix)
- ✓Pre-service automated check
- ✓Slack + Telegram alerts with escalation
- ✓Telegram remote control
- ✓Auto-recovery (stream restart)
- ✓Post-service incident timeline
- ✓Rundown planner with live show mode
- ✓Church Portal (self-service dashboard)
- ✓Email support
Plus
Full integrations, AI commands, and multi-room support for growing teams.
- ✓Everything in Connect
- ✓Up to 3 rooms
- ✓Signal failover (auto-switch to safe source on signal loss)
- ✓All 23 device integrations
- ✓Deep ProPresenter control (looks, timers, stage messages)
- ✓On-call TD rotation
- ✓Guest TD access tokens
- ✓Rundown: collaborative editing + AI document import
- ✓7 rundown output views (confidence monitor, teleprompter, etc.)
- ✓AI natural language commands
- ✓AI Autopilot (5 automation rules)
- ✓AI Setup Assistant (auto-configure from patch lists)
- ✓Priority email support
Pro
AI autopilot, Planning Center sync, and monthly reports for multi-room operations.
- ✓Everything in Plus
- ✓Up to 5 rooms
- ✓AI Autopilot (10 automation rules)
- ✓Planning Center sync + production write-back
- ✓Monthly health reports for leadership
- ✓Session recaps with full timeline
- ✓Priority support
Enterprise
Unlimited rooms, white-glove onboarding, and dedicated support.
- ✓Everything in Pro
- ✓Unlimited rooms
- ✓Dedicated onboarding & configuration
- ✓AI Autopilot (25 automation rules)
- ✓Custom autopilot rules built for you
- ✓Remote configuration changes
- ✓Monthly system health review
- ✓15-minute response SLA (Mon–Fri 9–5 ET + service windows)
- ✓Dedicated support engineer
All plans include email support at support@tallyconnect.app
Check hardware compatibility →
Compare plans side-by-side
Every plan starts with a 30-day free trial. All features included.
| Feature | Connect $79 $49/mo | Plus $99/mo | Pro $149/mo | Enterprise Custom |
|---|---|---|---|---|
| Rooms | 1 | 3 | 5 | Unlimited |
| ATEM / OBS / vMix Monitoring | ✓ | ✓ | ✓ | ✓ |
| Pre-Service Auto-Check | ✓ | ✓ | ✓ | ✓ |
| Slack + Telegram Alerts | ✓ | ✓ | ✓ | ✓ |
| Telegram Remote Control | ✓ | ✓ | ✓ | ✓ |
| Auto-Recovery (Stream Restart) | ✓ | ✓ | ✓ | ✓ |
| Post-Service Timeline | ✓ | ✓ | ✓ | ✓ |
| Church Portal | ✓ | ✓ | ✓ | ✓ |
| Signal Failover | — | ✓ | ✓ | ✓ |
| All 23 Integrations | 3 core | ✓ | ✓ | ✓ |
| Deep ProPresenter Control | — | ✓ | ✓ | ✓ |
| On-Call TD Rotation | — | ✓ | ✓ | ✓ |
TALLY BOX
Want zero-touch hardware?
Pre-configured encoder boxes that plug into your ATEM aux output. Ships ready — no setup, no IT, no port forwarding. Managed remotely from day one.
Tally Box Standard
Pre-configured Raspberry Pi encoder. Plug into your ATEM aux HDMI output — streams live video to your dashboard automatically.
- ✓Raspberry Pi 4 (4GB)
- ✓HDMI capture input
- ✓Pre-installed Tally software
- ✓Tailscale VPN + SSH for remote management
- ✓3Mbps H.264 monitoring stream
- ✓Remote config via Tally dashboard
Tally Box Pro
Intel NUC with Blackmagic capture. Supports HDMI and 3G-SDI — plugs directly into your ATEM SDI aux output.
- ✓Intel NUC mini PC
- ✓HDMI + 3G-SDI capture input
- ✓Pre-installed Tally software
- ✓Tailscale VPN + SSH for remote management
- ✓3Mbps H.264 monitoring stream
- ✓OBS, ProPresenter, audio console on same machine
WHAT CHURCHES SAY
Trusted by production teams
across the country
“Our stream dropped mid-sermon on Easter Sunday last year. This year Tally caught and recovered the drop in 8 seconds. Nobody in the congregation even noticed.”
“We went from needing a paid tech every Sunday to confident volunteers running the whole production. Tally handles the troubleshooting so they can focus on cameras and slides.”
“The pre-service check alone is worth the subscription. Every Sunday morning we get a green light 30 minutes before service. No more frantic booth walkthroughs.”
FAQ
Common questions.
30-day free trial. No credit card required. Cancel anytime.